structural mass造句
例句與造句
- The disadvantageous effect should be considered when the deflection between the structural mass center and stiffness center exists
摘要結構剛度中心與質量中心偏差較大時，應考慮扭轉的不利影響，將高層建筑結構等效為懸臂桿，從頂至底依次選取脫離體。 - In the second optimization model , the first mode frequency is decreased to let it below the frequency of brunt load and cut down greatly the structural mass
在第二個優化模型中，考慮減小泵車的一階頻率，盡量低于油缸沖擊載荷的頻率，同時可使結構質量有較大幅度下降。 - The structural optimization based on noise attenuation is studied , in which the thickness of each link is taken as the design variable , and the weighting sum of structural mass and measure of the structural acoustic performance is taken as the synthesis performance index
選取機構桿件厚度為設計變量，以機構質量和聲輻射性能量度的加權和為目標函數，應用改進了的變尺度優化算法對優化問題進行了求解。 - On the basis of the study of the characteristics of diffracted wave produced during the vibration propagation along the fissures , in association with practical example , the paper introduces the features of prospecting the depth of fissures of structural mass by using the seismic method
該文在研究振動沿裂縫傳播時所產生繞射波的特征基礎上，結合實例，介紹了運用地震法探測結構體裂縫深度的方法特點。 - Abstract : on the basis of the study of the characteristics of diffracted wave produced during the vibration propagation along the fissures , in association with practical example , the paper introduces the features of prospecting the depth of fissures of structural mass by using the seismic method
文摘:該文在研究振動沿裂縫傳播時所產生繞射波的特征基礎上，結合實例，介紹了運用地震法探測結構體裂縫深度的方法特點。 - It's difficult to find structural mass in a sentence. 用structural mass造句挺難的
- The structural optimization based on noise attenuation is studied , in which the thickness of each link is taken as the design variable , and the weighting sum of structural mass and measure of the structural acoustic performance is taken as the synthesis performance index
采用結構優化的方法對機構聲輻射控制問題進行了研究。選取機構桿件厚度為設計變量，以機構質量和聲輻射性能量度的加權和為目標函數，應用改進了的變尺度優化算法對優化問題進行了求解。 - In upper level optimization , the thickness and geometry factors of composite skins and webs as well as other structural dimensions are taken as design variables . then , considering the behavior constraints and the side constraints , the structural mass is minimized by the mathematical programming technique . in lower level optimization , the mathematical programming technique or the genetic algorithm ( ga ) is used to search the practical stacking sequence of composite skins and webs to realize the given thickness and geometry factors from upper level optimization
底層優化設西北工業大學博士學位論文計以復合材料蒙皮和腹板等層合板各分層的厚度(或鋪層數) 、鋪層角和鋪層順序?yàn)樵O(shè)計變量，以層合板的幾何因子與頂層優化設計給出的最優幾何因子之間的誤差最小為目標，考慮層合板厚度和制造工藝性約束，采用數學規劃方法或遺傳算法( geneticalgorithm ，簡稱ga )求出底層最優設計變量。